kascetopia.blogg.se - Zebra gx430t troubleshooting

#ZEBRA GX430T TROUBLESHOOTING MAC OSX#
#ZEBRA GX430T TROUBLESHOOTING INSTALL#
#ZEBRA GX430T TROUBLESHOOTING DRIVERS#
#ZEBRA GX430T TROUBLESHOOTING DRIVER#
#ZEBRA GX430T TROUBLESHOOTING MANUAL#

Wait for the group of two flashes, then release the feed button. Insert the roll of labels you plan to print from. In order to re-calibrate the printer follow these steps:

We have discovered that at times, especially when switching to new label types or sizes, the printer must be re-calibrated in order to properly detect the size and position of the labels. Included on one of these labels will be the printer's IP address. These labels contain diagnostic information about the printer. I don't know the IP address of my printer!Ī number of labels will be printed out. For instance, if you set up the printer using the "EPL2" driver, add the printer again using the "ZPL" driver, or vice versa.

#ZEBRA GX430T TROUBLESHOOTING MAC OSX#

On Windows and Mac OSX remove your printer and re-add it with an alternate driver. When successful, you will receive a printout that says "Out of dump." To remove the printer from "Dump" mode, simply click the feed button on the printer once. You may have also received a printout from your printer that looks like this: This may be happening because the printer is in "dump" mode. You are receiving an "unable to detect language" error The printer needs to detect the label size before it can print any labels. See below for more details on important functions. Each of these groups of flashes indicate a different function that the printer can perform. First it will flash once, then twice, then three times, etc. Holding down the feed will cause the light surrounding the feed button to alternate between being off and flashing in groups. This also quickly attempts to detect the size of the label. Pressing and releasing the feed button quickly will feed a single blank label. There are only a few that you will need to deal with when configuring your printer for Heartland Retail and/or troubleshooting issues.Īccessing these functions is accomplished by pressing/holding the green feed button. These functions should be outlined in your owners manual. Check power cable and turn printer on by power outlet.The Zebra LP 2824 Plus printer has a number of built-in functions that can be accessed via the feed button.

#ZEBRA GX430T TROUBLESHOOTING DRIVER#

Q: How do I print out the configuration and make setting changes to my printer?Ī: Print configuration label from driver under by accessing front panel menu under settings – Config.Ĭhange settings in driver and print windows test page (This will push commands changed to the printer). Please contact us for assistance in procuring a new printhead. Note: A gap in print may indicate a faulty printhead.

If Pause test prints darkness levels- Go into printer settings to adjust darkness.

If pause test does not show different darkness levels, labels and ribbon may be the wrong combo.

Pause Test - Hold pause while printer starts release pause after 5 seconds.

Q: How do I adjust the print quality from my printer?

#ZEBRA GX430T TROUBLESHOOTING INSTALL#

Driver installed under devices and printers on your PC should come online or a new driver will install automatically.

If driver is not communicating try using different connection cable.

Install driver with Network and then use settings while driver is installing to configure IP address.

Go to the Zebra GK420D driver section of this site to find an updated driver.

#ZEBRA GX430T TROUBLESHOOTING DRIVERS#

Q: How do I find and install new drivers for my printer?Ī: Follow the steps below to install new drivers for your printer.

#ZEBRA GX430T TROUBLESHOOTING MANUAL#

If Auto Calibrate does not run Manual calibration will need to be completed.

Auto calibrate should take place after printhead is closed.

Check that the ribbon is installed correctly.

Depending on labels the sensor will need to be positioned correctly.

Check your labels to define Gap, Notch or Mark.

Q: How do I calibrate or adjust my GK420D printer for the media / ribbon I wish to use?Ī: The below steps should be followed to resolve most issues with printer calibration. Visit this section of our site if you require information on the Zebra GK420D status lights, which explains the errors causing flashing red lights, amber lights etc. A wealth of self-help resources are available through our in-depth Knowledge Base. The document is organised as a set of individual questions and answers. We have put this Quick Troubleshooting Guide together to provide you with help in resolving some of the more common questions we receive in technical support. To assist you with keeping your critical operations running with the highest level of support for your Zebra printers.